loading

MERITSUN Battry - The Best Battery Energy Storage System & Lithium Battery Solutions Provider.

valve regulated lead acid battery Bring Dead Lead Acid Battery to Live Again

valve regulated lead acid battery Bring Dead Lead Acid Battery to Live Again

Today, we will learn how to re-use this method for dead sealed lead-acid batteries. I tried this with a lot of dead and expired batteries where 90% of them were re-used
S: This method may not bring the battery to full performance in its original state, but at my speed the battery will work 50% ~ 70%. you need : -3cm syringe -
Voltmeter or Multimeter
Battery Charger or power supply-
Crocodile line used with PSU-
Safe with distilled water: Do not touch the water from the battery using goggles and chemical gloves it is an acid sealed battery and we will find the lid on the top of the battery, just take it off with a flat screwdriver like a photo and we will find 3 holes covered by the rubber cap and now we have to remove the cap as well.
OK, now we will measure the voltage of this battery on my battery, it is 0. 76 volts only.
This means that the battery is completely dry from the inside. In this step, we need to fill the battery with distilled water to activate the acid again, so refill it with a syringe until the water measures the voltage from all the holes and you will find that the voltage increases mVolts, this is good, if not without worry, after filling the battery with the water we need, we need to make sure it is dry with the inside of the battery so reactivate it again first, we will charge with 12 v dc. The output "I Am using ATX PSU" is 10 Am psu. Now wait 5 minutes until you see the bubbles coming out of the hole
If there are no bubbles from any of the 3 holes, you have to reverse the positive and negative and wait up to 1 ~ 3 minutes (this is a dangerous step, don't leave the battery alone in this state) OK, now you have to see the bubbles cut off the power immediately from holes like boiling, and reconnect the Yin and positive holes again. Now pull the wasted water from the top of the 3 holes with a syringe and let the battery charge until it charges up to 6.
9 v u should check every 1 hour, then dry it with a paper towel and cover everything that congratulates your battery on working again. Can you ask me?
Sorry, my English is not good! !

GET IN TOUCH WITH Us
recommended articles
Knowledge Successful case News
Greenhouse Battery Backup Planning: Controls, Pumps, Fans and Lighting
Plan greenhouse battery backup by prioritizing controls, alarms, irrigation, fans, pumps and lighting, then checking startup power, runtime, SOC reserve and transfer behavior.
How to Size Battery Backup for a Small Studio or Home Business
Size battery backup for a studio, shop or home business by defining critical loads, peak power, usable energy, transfer needs, SOC reserve and recharge strategy.
IP65 Outdoor Home Battery Installation: What Installers Must Verify Beyond the Rating
Learn what IP65 covers, what it does not, and what installers must verify for outdoor home batteries: location, heat, drainage, corrosion, cable entries and commissioning.
What Information Is Needed for a Residential Energy Storage Quote?
Use this residential ESS RFQ checklist to submit the grid, load, PV, inverter, backup, site, approval and commercial data needed for a usable quote.
How to Compare Home Battery Quotes: A Bid-Normalization Guide for Installers and Distributors
A practical bid-normalization guide for comparing home battery energy, power, inverter scope, approvals, commissioning, warranty and support.
Nominal vs. Usable Home Battery Capacity: What Installers Should Calculate Before Quoting Runtime
Learn how nominal kWh, starting SOC, reserve settings, conversion losses and load profile determine usable home-battery energy and backup runtime.
Is 128 kWh Enough for Whole-Home Backup? Inside a Caribbean Residential Installation
See how a 128 kWh MERITSUN battery bank, 28.8 kWp solar array and Schneider inverter platform support whole-home backup in Punta Cana.
Project Complete: 48 kWh Whole-Home Storage With Three MSP-6KW Units
A 48 kWh MERITSUN home storage system is now in service, using three 6 kW all-in-one units to support separate household load groups.
60 kWh Farm Battery Storage in the U.S.: What This 12-Module Project Shows
Analyze the design logic behind a U.S. farm project using 12 parallel MERITSUN battery modules, a 60 kWh-class battery bank and a Schneider inverter.
Home Battery Sizing Guide for Solar Installers: 10kWh, 20kWh and 30kWh Systems
A practical MERITSUN home battery sizing guide comparing 10kWh, 20kWh and 30kWh systems for solar installers, EPCs, dealers and distributors.
Established in 1999, we have 20+ years of energy professional experience and integrated solutions services in energy storage application industrial, and further reach the demands the smart & green energy era. 
Copyright ©1999-2025 MeriTech Power Limited - www.meritsunpower.com | All Rights Reserved | Sitemap | Privacy Policy
Customer service
detect